CVE-2026-16515 (GCVE-0-2026-16515)
Vulnerability from cvelistv5 – Published: 2026-09-18 14:30 – Updated: 2026-09-18 16:26
VLAI
EPSS
VEX
Title
ICMPv6 error messages sent for multicast-destined packets and non-unique source addresses enable network amplification in Zephyr's IPv6 stack
Summary
net_icmpv6_send_error() in subsys/net/ip/icmpv6.c implemented only one of the three RFC 4443 section 2.4 suppression rules (do not answer an ICMPv6 error with an ICMPv6 error). It did not check whether the triggering packet's source address identifies a single node (rule e.6) or whether the packet was sent to a multicast destination (rule e.3, whose only exceptions are Packet Too Big and Parameter Problem Code 2). Of the five call sites, only the port-unreachable path in subsys/net/ip/connection.c carried an equivalent guard of its own; the extension-header, unknown-next-header and fragmentation paths in subsys/net/ip/ipv6.c and subsys/net/ip/ipv6_fragment.c had none.
An unauthenticated attacker with access to the same link can exploit this in two ways. Sending a single IPv6 packet to the link-local all-nodes group ff02::1 carrying an unrecognized next-header value, with the source address spoofed to a chosen victim, causes every Zephyr node on the link to emit an ICMPv6 Parameter Problem message to that victim — a reflector with an amplification factor equal to the number of nodes. Alternatively, sending a unicast packet whose source address is a multicast address causes the node to transmit its ICMPv6 error to that multicast address, turning one unicast packet into a link-flooded multicast frame. Packets addressed to ff02::1 are accepted unconditionally by ipv6_input(), and no check rejects a multicast source address, so no special configuration is required.
The impact is degraded availability of the shared link and of the reflection victim, together with the ability for the attacker to hide its own address behind the responding nodes. The effect is amplified on constrained mesh links such as 802.15.4/Thread, where link-local multicast is flooded hop by hop. There is no memory-safety consequence: the error packet itself is well formed, it is simply emitted in cases where the protocol forbids it.
The fix adds both suppression checks at the single choke point in net_icmpv6_send_error(), before any reply packet is allocated, preserving the RFC-mandated exceptions for NET_ICMPV6_PACKET_TOO_BIG and Parameter Problem Code 2. Note that the IPv4 counterpart net_icmpv4_send_error() in subsys/net/ip/icmpv4.c still checks only for a broadcast destination and retains an equivalent gap for multicast destinations and non-unique sources.
Severity
4.7 (Medium)
SSVC
Exploitation: none
Automatable: no
Technical Impact: partial
CISA Coordinator · CISA-ADP (v2.0.3)
Decision recorded 2026-09-18 16:25 UTC
CWE
- CWE-406 - dos
Assigner
References
2 references
Impacted products
1 product
| Vendor | Product | Version | CPE status | |
|---|---|---|---|---|
| zephyrproject | zephyr |
Affected:
1.14.0 , < 4.4.2
(semver)
|
guessed |
{
"containers": {
"adp": [
{
"metrics": [
{
"other": {
"content": {
"id": "CVE-2026-16515",
"options": [
{
"Exploitation": "none"
},
{
"Automatable": "no"
},
{
"Technical Impact": "partial"
}
],
"role": "CISA Coordinator",
"timestamp": "2026-09-18T16:25:27.449454Z",
"version": "2.0.3"
},
"type": "ssvc"
}
}
],
"providerMetadata": {
"dateUpdated": "2026-09-18T16:26:05.219Z",
"orgId": "134c704f-9b21-4f2e-91b3-4a467353bcc0",
"shortName": "CISA-ADP"
},
"title": "CISA ADP Vulnrichment"
}
],
"cna": {
"affected": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"subsys/net/ip/icmpv6.c"
],
"programRoutines": [
{
"name": "net_icmpv6_send_error"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThan": "4.4.2",
"status": "affected",
"version": "1.14.0",
"versionType": "semver"
}
]
}
],
"descriptions": [
{
"lang": "en",
"value": "net_icmpv6_send_error() in subsys/net/ip/icmpv6.c implemented only one of the three RFC 4443 section 2.4 suppression rules (do not answer an ICMPv6 error with an ICMPv6 error). It did not check whether the triggering packet\u0027s source address identifies a single node (rule e.6) or whether the packet was sent to a multicast destination (rule e.3, whose only exceptions are Packet Too Big and Parameter Problem Code 2). Of the five call sites, only the port-unreachable path in subsys/net/ip/connection.c carried an equivalent guard of its own; the extension-header, unknown-next-header and fragmentation paths in subsys/net/ip/ipv6.c and subsys/net/ip/ipv6_fragment.c had none.\n\nAn unauthenticated attacker with access to the same link can exploit this in two ways. Sending a single IPv6 packet to the link-local all-nodes group ff02::1 carrying an unrecognized next-header value, with the source address spoofed to a chosen victim, causes every Zephyr node on the link to emit an ICMPv6 Parameter Problem message to that victim \u2014 a reflector with an amplification factor equal to the number of nodes. Alternatively, sending a unicast packet whose source address is a multicast address causes the node to transmit its ICMPv6 error to that multicast address, turning one unicast packet into a link-flooded multicast frame. Packets addressed to ff02::1 are accepted unconditionally by ipv6_input(), and no check rejects a multicast source address, so no special configuration is required.\n\nThe impact is degraded availability of the shared link and of the reflection victim, together with the ability for the attacker to hide its own address behind the responding nodes. The effect is amplified on constrained mesh links such as 802.15.4/Thread, where link-local multicast is flooded hop by hop. There is no memory-safety consequence: the error packet itself is well formed, it is simply emitted in cases where the protocol forbids it.\n\nThe fix adds both suppression checks at the single choke point in net_icmpv6_send_error(), before any reply packet is allocated, preserving the RFC-mandated exceptions for NET_ICMPV6_PACKET_TOO_BIG and Parameter Problem Code 2. Note that the IPv4 counterpart net_icmpv4_send_error() in subsys/net/ip/icmpv4.c still checks only for a broadcast destination and retains an equivalent gap for multicast destinations and non-unique sources."
}
],
"metrics": [
{
"cvssV3_1": {
"baseScore": 4.7,
"baseSeverity": "MEDIUM",
"vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:L",
"version": "3.1"
},
"format": "CVSS"
}
],
"problemTypes": [
{
"descriptions": [
{
"cweId": "CWE-406",
"description": "dos",
"lang": "en",
"type": "CWE"
}
]
}
],
"providerMetadata": {
"dateUpdated": "2026-09-18T14:30:13.017Z",
"orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"shortName": "zephyr"
},
"references": [
{
"name": "Fix commit",
"tags": [
"patch"
],
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/ba4247b24ddd3a5360b617e3ca17131ca9e8026a"
},
{
"name": "GHSA-v5vw-m78m-h46g",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-v5vw-m78m-h46g"
}
],
"title": "ICMPv6 error messages sent for multicast-destined packets and non-unique source addresses enable network amplification in Zephyr\u0027s IPv6 stack",
"x_generator": {
"engine": "cvelib 1.8.0"
}
}
},
"cveMetadata": {
"assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"assignerShortName": "zephyr",
"cveId": "CVE-2026-16515",
"datePublished": "2026-09-18T14:30:13.017Z",
"dateReserved": "2026-07-21T21:43:00.776Z",
"dateUpdated": "2026-09-18T16:26:05.219Z",
"state": "PUBLISHED"
},
"dataType": "CVE_RECORD",
"dataVersion": "5.2",
"vulnerability-lookup:meta": {
"nvd": {
"cve": {
"affected": [
{
"affectedData": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"subsys/net/ip/icmpv6.c"
],
"programRoutines": [
{
"name": "net_icmpv6_send_error"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThan": "4.4.2",
"status": "affected",
"version": "1.14.0",
"versionType": "semver"
}
]
}
],
"source": "vulnerabilities@zephyrproject.org"
}
],
"cveTags": [],
"descriptions": [
{
"lang": "en",
"value": "net_icmpv6_send_error() in subsys/net/ip/icmpv6.c implemented only one of the three RFC 4443 section 2.4 suppression rules (do not answer an ICMPv6 error with an ICMPv6 error). It did not check whether the triggering packet\u0027s source address identifies a single node (rule e.6) or whether the packet was sent to a multicast destination (rule e.3, whose only exceptions are Packet Too Big and Parameter Problem Code 2). Of the five call sites, only the port-unreachable path in subsys/net/ip/connection.c carried an equivalent guard of its own; the extension-header, unknown-next-header and fragmentation paths in subsys/net/ip/ipv6.c and subsys/net/ip/ipv6_fragment.c had none.\n\nAn unauthenticated attacker with access to the same link can exploit this in two ways. Sending a single IPv6 packet to the link-local all-nodes group ff02::1 carrying an unrecognized next-header value, with the source address spoofed to a chosen victim, causes every Zephyr node on the link to emit an ICMPv6 Parameter Problem message to that victim \u2014 a reflector with an amplification factor equal to the number of nodes. Alternatively, sending a unicast packet whose source address is a multicast address causes the node to transmit its ICMPv6 error to that multicast address, turning one unicast packet into a link-flooded multicast frame. Packets addressed to ff02::1 are accepted unconditionally by ipv6_input(), and no check rejects a multicast source address, so no special configuration is required.\n\nThe impact is degraded availability of the shared link and of the reflection victim, together with the ability for the attacker to hide its own address behind the responding nodes. The effect is amplified on constrained mesh links such as 802.15.4/Thread, where link-local multicast is flooded hop by hop. There is no memory-safety consequence: the error packet itself is well formed, it is simply emitted in cases where the protocol forbids it.\n\nThe fix adds both suppression checks at the single choke point in net_icmpv6_send_error(), before any reply packet is allocated, preserving the RFC-mandated exceptions for NET_ICMPV6_PACKET_TOO_BIG and Parameter Problem Code 2. Note that the IPv4 counterpart net_icmpv4_send_error() in subsys/net/ip/icmpv4.c still checks only for a broadcast destination and retains an equivalent gap for multicast destinations and non-unique sources."
}
],
"id": "CVE-2026-16515",
"lastModified": "2026-09-18T19:11:57.760",
"metrics": {
"cvssMetricV31": [
{
"cvssData": {
"attackComplexity": "LOW",
"attackVector": "ADJACENT_NETWORK",
"availabilityImpact": "LOW",
"baseScore": 4.7,
"baseSeverity": "MEDIUM",
"confidentialityImpact": "NONE",
"integrityImpact": "NONE",
"privilegesRequired": "NONE",
"scope": "CHANGED",
"userInteraction": "NONE",
"vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:L",
"version": "3.1"
},
"exploitabilityScore": 2.8,
"impactScore": 1.4,
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
],
"ssvcV203": [
{
"source": "134c704f-9b21-4f2e-91b3-4a467353bcc0",
"ssvcData": {
"id": "CVE-2026-16515",
"options": [
{
"exploitation": "none"
},
{
"automatable": "no"
},
{
"technicalImpact": "partial"
}
],
"role": "CISA Coordinator",
"timestamp": "2026-09-18T16:25:27.449454Z",
"version": "2.0.3"
}
}
]
},
"published": "2026-09-18T15:17:05.897",
"references": [
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/ba4247b24ddd3a5360b617e3ca17131ca9e8026a"
},
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-v5vw-m78m-h46g"
}
],
"sourceIdentifier": "vulnerabilities@zephyrproject.org",
"vulnStatus": "Awaiting Analysis",
"weaknesses": [
{
"description": [
{
"lang": "en",
"value": "CWE-406"
}
],
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
]
}
},
"vulnrichment": {
"containers": {
"adp": [
{
"metrics": [
{
"other": {
"content": {
"id": "CVE-2026-16515",
"options": [
{
"Exploitation": "none"
},
{
"Automatable": "no"
},
{
"Technical Impact": "partial"
}
],
"role": "CISA Coordinator",
"timestamp": "2026-09-18T16:25:27.449454Z",
"version": "2.0.3"
},
"type": "ssvc"
}
}
],
"providerMetadata": {
"dateUpdated": "2026-09-18T16:25:46.803Z",
"orgId": "134c704f-9b21-4f2e-91b3-4a467353bcc0",
"shortName": "CISA-ADP"
},
"title": "CISA ADP Vulnrichment"
}
],
"cna": {
"affected": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"subsys/net/ip/icmpv6.c"
],
"programRoutines": [
{
"name": "net_icmpv6_send_error"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThan": "4.4.2",
"status": "affected",
"version": "1.14.0",
"versionType": "semver"
}
]
}
],
"descriptions": [
{
"lang": "en",
"value": "net_icmpv6_send_error() in subsys/net/ip/icmpv6.c implemented only one of the three RFC 4443 section 2.4 suppression rules (do not answer an ICMPv6 error with an ICMPv6 error). It did not check whether the triggering packet\u0027s source address identifies a single node (rule e.6) or whether the packet was sent to a multicast destination (rule e.3, whose only exceptions are Packet Too Big and Parameter Problem Code 2). Of the five call sites, only the port-unreachable path in subsys/net/ip/connection.c carried an equivalent guard of its own; the extension-header, unknown-next-header and fragmentation paths in subsys/net/ip/ipv6.c and subsys/net/ip/ipv6_fragment.c had none.\n\nAn unauthenticated attacker with access to the same link can exploit this in two ways. Sending a single IPv6 packet to the link-local all-nodes group ff02::1 carrying an unrecognized next-header value, with the source address spoofed to a chosen victim, causes every Zephyr node on the link to emit an ICMPv6 Parameter Problem message to that victim \u2014 a reflector with an amplification factor equal to the number of nodes. Alternatively, sending a unicast packet whose source address is a multicast address causes the node to transmit its ICMPv6 error to that multicast address, turning one unicast packet into a link-flooded multicast frame. Packets addressed to ff02::1 are accepted unconditionally by ipv6_input(), and no check rejects a multicast source address, so no special configuration is required.\n\nThe impact is degraded availability of the shared link and of the reflection victim, together with the ability for the attacker to hide its own address behind the responding nodes. The effect is amplified on constrained mesh links such as 802.15.4/Thread, where link-local multicast is flooded hop by hop. There is no memory-safety consequence: the error packet itself is well formed, it is simply emitted in cases where the protocol forbids it.\n\nThe fix adds both suppression checks at the single choke point in net_icmpv6_send_error(), before any reply packet is allocated, preserving the RFC-mandated exceptions for NET_ICMPV6_PACKET_TOO_BIG and Parameter Problem Code 2. Note that the IPv4 counterpart net_icmpv4_send_error() in subsys/net/ip/icmpv4.c still checks only for a broadcast destination and retains an equivalent gap for multicast destinations and non-unique sources."
}
],
"metrics": [
{
"cvssV3_1": {
"baseScore": 4.7,
"baseSeverity": "MEDIUM",
"vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:L",
"version": "3.1"
},
"format": "CVSS"
}
],
"problemTypes": [
{
"descriptions": [
{
"cweId": "CWE-406",
"description": "dos",
"lang": "en",
"type": "CWE"
}
]
}
],
"providerMetadata": {
"dateUpdated": "2026-09-18T14:30:13.017Z",
"orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"shortName": "zephyr"
},
"references": [
{
"name": "Fix commit",
"tags": [
"patch"
],
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/ba4247b24ddd3a5360b617e3ca17131ca9e8026a"
},
{
"name": "GHSA-v5vw-m78m-h46g",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-v5vw-m78m-h46g"
}
],
"title": "ICMPv6 error messages sent for multicast-destined packets and non-unique source addresses enable network amplification in Zephyr\u0027s IPv6 stack",
"x_generator": {
"engine": "cvelib 1.8.0"
}
}
},
"cveMetadata": {
"assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"assignerShortName": "zephyr",
"cveId": "CVE-2026-16515",
"datePublished": "2026-09-18T14:30:13.017Z",
"dateReserved": "2026-07-21T21:43:00.776Z",
"dateUpdated": "2026-09-18T16:26:05.219Z",
"state": "PUBLISHED"
},
"dataType": "CVE_RECORD",
"dataVersion": "5.2"
}
}
}
Loading…
Loading…
Experimental. This forecast is provided for visualization only and may change without notice. Do not use it for operational decisions.
Forecast uses a logistic model when the trend is rising, or an exponential decay model when the trend is falling. Fitted via linearized least squares.
Sightings
| Author | Source | Type | Date | Other |
|---|
Nomenclature
- Seen: The vulnerability was mentioned, discussed, or observed by the user.
- Confirmed: The vulnerability has been validated from an analyst's perspective.
- Published Proof of Concept: A public proof of concept is available for this vulnerability.
- Exploited: The vulnerability was observed as exploited by the user who reported the sighting.
- Patched: The vulnerability was observed as successfully patched by the user who reported the sighting.
- Not exploited: The vulnerability was not observed as exploited by the user who reported the sighting.
- Not confirmed: The user expressed doubt about the validity of the vulnerability.
- Not patched: The vulnerability was not observed as successfully patched by the user who reported the sighting.
Loading…
The MITRE ATT&CK techniques below are AI-generated suggestions, inferred from the description of the
vulnerability by the CIRCL/vulnerability-attack-technique-classification-roberta-base
model, served locally by ML-Gateway.
They have not been verified by an analyst and are provided for guidance only.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
Loading…
Related by attack behaviour
Vulnerabilities whose description is nearest to this one in the vector space of the CIRCL/vulnerability-attack-technique-biencoder model. This is a similarity search over the bi-encoder space (plain cosine), not a classification, and it has no measured accuracy.
Loading…