https://vulnerability.circl.lu Contains only the most 10 recent entries. http://www.rssboard.org/rss-specification python-feedgen en Mon, 05 Oct 2026 15:18:57 +0000 https://vulnerability.circl.lu/vuln/cve-2022-49613 <p><strong>Affected:</strong> Linux</p> <p>In the Linux kernel, the following vulnerability has been resolved:</p> <p>serial: 8250: Fix PM usage_count for console handover</p> <p>When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()):</p> <p>[ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit ttyS0 usage:0 [ 1.977075] serial8250 serial8250: Runtime PM usage count underflow! [ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A [ 1.977812] univ8250_console_setup ttyS0 usage:2 [ 1.978167] printk: console [ttyS0] printing thread started [ 1.978203] printk: console [ttyS0] enabled</p> <p>To fix the issue, call pm_runtime_get_sync() in serial8250_register_ports() as soon as .dev is set for an uart_port if it has console enabled.</p> <p>This pro…</p> <p><strong>Affected:</strong> Linux</p> <p>In the Linux kernel, the following vulnerability has been resolved:</p> <p>serial: 8250: Fix PM usage_count for console handover</p> <p>When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()):</p> <p>[ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit ttyS0 usage:0 [ 1.977075] serial8250 serial8250: Runtime PM usage count underflow! [ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A [ 1.977812] univ8250_console_setup ttyS0 usage:2 [ 1.978167] printk: console [ttyS0] printing thread started [ 1.978203] printk: console [ttyS0] enabled</p> <p>To fix the issue, call pm_runtime_get_sync() in serial8250_register_ports() as soon as .dev is set for an uart_port if it has console enabled.</p> <p>This pro…</p> https://vulnerability.circl.lu/vuln/cve-2022-49613